DEPARTMENT 101                             STONEY ROBERTS DEMOLITION DERBY

SET# 1 STONEY ROBERTS DEMOLITION DERBY                                                                  BUY TICKETS TODAY!

FULL SIZE 8 & 6 CYLINDERS HARDTOP AUTOMOBILES        

DOMESTIC OR FOREIGN

1. 8 Cyl or 6 Cyl STOCK HARDTOP AUTOMOBILES OR STATION WAGONS ARE ALLOWED THIS INCLUDES FOREIGN AUTO'S. You may use

front wheel drive vehicles. No trucks, jeeps, hearses, limo's, ambulances, convertibles, SUV's, Rear engine auto's, 4 x 4s, Camaros, Firebirds and El

Caminos, Chrysler Imperials or Imperial Sub Frames. Full Size auto's must have a Wheel Base of 105" or greater. Wheel base is measured center of

hub to center of hub.

2. ALL GLASS AND CHROME TRIM and anything that might become imbedded in the track, must be removed from the car before bringing auto to

the grounds. Also, car must be cleaned out, including trunk. Fire walls must remain in place. They cannot be sectioned or deleted. Do not leave

broken glass in doors, clean them out. WINDSHIELDS MUST BE REMOVED. All AIR BAG SAFETY SYSTEMS this includes activation charges must

be removed.

3. TIRES MUST BE STOCK SIZE, 4 ply only, Maximum rated 45 lbs PSI pressure, Mud & Snow okay, no inner liner, no truck or light truck tires

(LT's), no paddle tires with tractor or ATV aggressive tread. No spoked rims, valve stem guards, or tires held on by being screwed to the rims. Tires

can only be filled with air, no fluids or solids ( tires within a tire are considered reinforcements ) ( tires marked tubeless may have tubes inserted in

them.) Remove all wheel balance weights.

4. A MAXIMUM OF FIVE (5) GALLONS OF GASOLINE WILL BE ALLOWED. GAS TANKS behind the axle should be moved to the trunk or to the

driver's compartment back seat area. If in drivers compartment the tanks must be completely covered by a Metal firewall. If gas tanks are located in

front of the rear axle they can be left in place but should be covered with a skid plate ( between ground and tank) to prevent them from being

damaged, from the ground side. Only unleaded gasoline with a maximum octane level of 93 will be permitted. BOOSTED or RACING FUEL will not

be allowed. If you have a car equipped with a fuel pump in the gas tank, you must install a emergency cut off switch upon the dash with a red circle

painted around it. No external fuel pumps will be allowed within the drivers compartment. If you run gas lines in the drivers compartment they must be

double lined & double clamped. (a fuel line within another line.)

5. ONLY ONE (1) STOCK BATTERY will be allowed. A maximum of 850 cold cranking amps will be permitted. It must be incased in some way to

catch any leaking acid if it should become ruptured. It may be moved into the passenger floorboard area. Must be mounted & covered for participants

protection.

6. NO REINFORCEMENTS OF ANY KIND WILL BE ALLOWED. Only exception will be the driver side front door. Reinforcement bars or plates

added to the drivers side door may not exceed eight inches (8") past the vertical seams of the door. Trailer hitches or any type of stiffening device are

considered reinforcements. You may Weld rear ends or differentials to create a positive traction rear end. Rear ends cannot be chained No truck rearends,

no flipping of rear-ends, no leaf spring conversions, or leaf over conversions will be permitted. No solid shocks or adding extra clamps or springs

to suspension (suspension must work). Vehicles that came stock with leaf springs can have no more than six leafs per a side.. Welding of bumper

shocks are considered reinforcements. Maximum bumper height is 24 inches from the ground to the center of the bumper for V 6 & V 8s. You may

insert up to three bars in the windshield opening to prevent hood collapsing back upon driver.

7. STANDARD EXHAUST SYSTEM may be removed or cut off just aft of the front seats. Do not position exhaust to deflect the heat out to the side of

the vehicle. Additional headers, stacks, or custom manifolds cannot protrude past the level of the hood or through the body of the car etc.

8. DO NOT WELD OR BOLT hood or trunk lids down with any type all thread bolts or rods.. Use wire only on up to six points of hoods. Trunks can be

chained shut in four places only. All doors must be Chained shut or welded (Chain is preferred on at least one door to allow for quick removal of

injured participants). If doors are welded a maximum of three (3) , four inch (4") welds in length on the two vertical seams per a door will be permitted.

If a driver's side door comes open, he or she will be disqualified.

9. A 12 BY 15 INCH HOLE must be cut into the center of hood. To allow for early fire detection. ALL Metal Fan Blades must be removed. They may

be replaced with polycarbonate plastic blades. Only exception will be if your car is equipped with a slip clutch fan blade and fan shroud or came stock

with an electric fan and shroud. You may create your own fan shroud out of some type of thin metal material & replace stiff original fans with slip

clutch fans. You may use electric fans ( only one) on cars that did not come equipped with them from the factory.

10. PRIOR TO BRINGING CARS TO FAIRGROUND radiators must be drained and back flushed of all antifreeze coolants. They then can be refilled

with water or any of the new naturally biodegradable coolants. You must evacuate all air conditioning apparatus (lines & pumps) and gas refrigerant

coolants from your vehicles. Transmission coolers may be used but must stay within the engine compartment. (under the hood)

11. SAFETY BELTS, HELMETS (DOT approve), AND IMPACT RESISTANT EYE PROTECTORS are required. If car was equipped with a shoulder

restraint system including lap belt, both must be used. Driver can be disqualified at any time if either belt or helmet is removed during a heat. Diver's

must wear long sleeve shirts & Pants. No electronic communications between driver and any other individuals permitted. NO TWO WAY RADIO'S. No

deliberate head-on collisions or deliberately ramming a driver's door. This can lead to disqualification. A TIME LIMIT will be set by the judges. IF A

DRIVER DOES NOT HIT A LIVE CAR WITHIN THE TIME LIMIT, this can lead to disqualification. No Possums!

12. ADDITIONAL SAFETY REGULATIONS MAY BE IMPOSED depending on the track. Rules are subject to change to fi t the event . If you have any

safety concerns. Call 1-888-361-5767 THE DECISION OF JUDGE IS FINAL. ANY DRIVER NOT OBEYING THE RULES WILL BE

DISQUALIFIED.

13. ALL CARS MUST BE REMOVED FROM GROUNDS BY THE OWNER NO

 

SET# 3 STONEY ROBERTS DEMOLITION DERBY

4 or 6 CYLINDER MINIVANS

DOMESTIC OR FOREIGN

A minivan, multi-purpose vehicle (abbreviated MPV), people-carrier, people-mover is a type of

automobile similar in shape to a van that is designed for personal use. Minivans are taller than a

sedan, hatchback or a station wagon, and are designed for maximum interior room. Three types of

Minivans exist Large Minivans, Compact Minivans and Micro Minivans. For the purpose of Demolition

Derbies that we produce we will only use the Large Minivan Category. These will be Minivans that

exceed overall Length of 168 inches. (This is not wheelbase but overall vehicle length).

1. ANY MINIVAN Foreign or Domestic 4 or 6 Cyl models. All engines must be forward of the front seats. You may use four wheeled drive models: If

four wheeled drive one of the drive trains must be disconnected (Your Choice). Minivans must have an overall length of at least 168 inches. No

Compact Minivans or Micro-minivans will be permitted. No snub or flat nose Minivans are permitted.

2. ALL GLASS AND CHROME TRIM and anything that might become imbedded in the track, must be removed from the car before bringing auto to

the grounds. Also, car must be cleaned out, including trunk. Fire walls must remain in place. They cannot be sectioned or deleted. Do not leave

broken glass in doors, clean them out. WINDSHIELDS MUST BE REMOVED. All AIR BAG SAFETY SYSTEMS this includes activation charges must

be removed.

3. TIRES MUST BE STOCK SIZE, 4 ply only Passenger rated tire. Maximum size 15 inches. Maximum rated 45 lbs PSI pressure, Mud & Snow

okay, no inner liner, no truck or light truck tires (LT's), no paddle tires with tractor or ATV aggressive tread. No spoked rims, valve stem guards, or tires

held on by being screwed to the rims. Tires can only be filled with air, no fluids or solids ( tires within a tire are considered reinforcements ) ( tires

marked tubeless may have tubes inserted in them.) Remove all wheel balance weights inside and out.

4. A MAXIMUM OF FIVE (5) GALLONS OF GASOLINE WILL BE ALLOWED. GAS TANKS behind the axle should be moved to the trunk or to the

driver's compartment back seat area. If in drivers compartment the tanks must be completely covered by a Metal firewall. If gas tanks are located in

front of the rear axle they can be left in place but should be covered with a skid plate ( between ground and tank) to prevent them from being

damaged, from the ground side. Only unleaded gasoline with a maximum octane level of 93 will be permitted. BOOSTED or RACING FUEL will not

be allowed. If you have a car equipped with a fuel pump in the gas tank, you must install a emergency cut off switch upon the dash with a red circle

painted around it. No external fuel pumps will be allowed within the drivers compartment. If you run gas lines in the drivers compartment they must be

double lined & double clamped. (a fuel line within another line.)

5. ONLY ONE (1) STOCK BATTERY will be allowed. A maximum of 850 cold cranking amps will be permitted. It must be incased in some way to

catch any leaking acid if it should become ruptured. It may be moved into the passenger floorboard area. Must be mounted & covered for participants

protection.

6. NO REINFORCEMENTS OF ANY KIND WILL BE ALLOWED. Only exception will be the driver side front door. Reinforcement bars or plates

added to the drivers side doors may not exceed eight inches (8") past the vertical seams of the door. Trailer hitches or any type of stiffening device are

considered reinforcements. You may Weld rear ends or differentials to create a positive traction rear end. Rear ends cannot be chained. No

interchangeable rear ends. Only stock rear ends. No mini truck rear ends No solid shocks or adding extra clamps or springs to suspension

(suspension must work). Welding of bumper shocks are considered reinforcements. Maximum bumper height is 20 inches from the ground to the

center of the bumper. It is suggested that you attach two vertical metal rods or chains approximately 12 inches from each end of the windshield

opening to protect driver from hood coming off of hinges and collapsing back in to the driver compartment. If your Minivan has a interior DOG HOUSE

ENGINE COVER it must be secured and not be removable.

7. STANDARD EXHAUST SYSTEM may be removed or cut off just aft of the front seats. Do not position exhaust to deflect the heat out to the side of

the vehicle. Additional headers, stacks, or custom manifolds cannot protrude past the level of the hood or through the body of the car etc.

8. DO NOT WELD OR BOLT hood or trunk lids down with any type all thread bolts or rods. Use wire only on up to six points of hoods. Trunks can be

chained shut in four places only. All doors must be Chained shut or welded (Chain is preferred on at least one door to allow for quick removal of injured

participants). If doors are welded a maximum of three (3) , four inch (4") welds in length on the two vertical seams per a door will be permitted. If a

driver's side door comes open, he or she will be disqualified.

9. A 10 BY 12 INCH HOLE must be cut into the center of hood. To allow for early fire detection. ALL Metal Fan Blades must be removed. They may

be replaced with polycarbonate plastic blades. Only exception will be if your car is equipped with a slip clutch fan blade and fan shroud or came stock

with an electric fan and shroud. You may create your own fan shroud out of some type of thin metal material & replace stiff original fans with slip

clutch fans. You may use electric fans ( only one) on cars that did not come equipped with them from the factory.

10. PRIOR TO BRINGING CARS TO FAIRGROUND radiators must be drained and back flushed of all antifreeze coolants. They then can be refilled

with water or any of the new naturally biodegradable coolants. You must evacuate all air conditioning apparatus (lines & pumps) and gas refrigerant

coolants from your vehicles. Transmission coolers may be used but must stay within the engine compartment. (under the hood)

11. SAFETY BELTS, HELMETS (DOT approve), AND IMPACT RESISTANT EYE PROTECTORS are required. If car was equipped with a shoulder

restraint system including lap belt, both must be used. Driver can be disqualified at any time if either belt or helmet is removed during a heat. Diver's

must wear long sleeve shirts & Pants. No electronic communications between driver and any other individuals permitted. NO TWO WAY RADIO'S. No

deliberate head-on collisions or deliberately ramming a driver's door. This can lead to disqualification. A TIME LIMIT will be set by the judges. IF A

DRIVER DOES NOT HIT A LIVE CAR WITHIN THE TIME LIMIT, this can lead to disqualification. No Possums!

12. ADDITIONAL SAFETY REGULATIONS MAY BE IMPOSED depending on the track. Rules are subject to change to fi t the event . If you have any

safety concerns. Call 1-888-361-5767 THE DECISION OF JUDGE IS FINAL. ANY DRIVER NOT OBEYING THE RULES WILL BE

DISQUALIFIED.

13. ALL CARS MUST BE REMOVED FROM GROUNDS BY THE OWNER NO LATER THAN 7:00 A.M. THE NEXT DAY FOLLOWING THE DERBY.

THIS IS YOUR RESPONSIBILITY, so make arrangements before derby time.

Example of types of Mini Vans that you may consider top use.

Chrysler Mini Van

Honda Odyssey

Pontiac Montana

Olds Silhouette

Ford Windstar

Toyota Sienna

Chevy Venture

Dodge Caravan

Chrysler Voyager

Dodge Grand Caravan

Mazda MPV

Nissan Quest

Chevy Astro

Mercury Villager

Chrysler Town Country

Plymouth Voyager

Renault Space

Honda FR-V

GC Safari

Fiat Multiplan

Fiat Ulysses

Chevrolet Uplander

Mercedes-Benz R-Class

Ford Galaxy

Set  #4 STONEY ROBERTS DEMOLITION DERY

4 or 6 Cylinder Compact Pick-up Truck

DOMESTIC OR FOREIGN

1. ANY FOREIGN OR DOMESTIC STOCK 4 or 6 Cyl Compact Pick-up Truck. Truck may be two or four door with extended cab. You may use

four wheeled drive models: if four wheeled drive one of the drive trains must be disconnected (Your Choice). No Soft tops or Fiberglass tops. No Mid

size pick-ups

2. ALL GLASS AND CHROME TRIM and anything that might become imbedded in the track, must be removed from the truck before bringing it to the

grounds. Also, Fire walls must remain in place. They cannot be sectioned or deleted. Do not leave broken glass in doors, clean them out.

WINDSHIELDS MUST BE REMOVED. All AIR BAG SAFETY SYSTEMS this includes activation charges must be removed. You must place some type

of screen in two door pick-ups back glass opening to prevent arms or head from extending from the opening. It is suggested to pad drivers side doors &

rig a headrest or padding behind all two door truck seats to protect the driver also.

3. TIRES MUST BE STOCK SIZE, Truck tires can be up to 8 ply, no inner liner, no wire spoked rims, no split rims. Mud & Snow okay, no paddle

tires with tractor or ATV aggressive tread. No spoked rims, valve stem guards, or tires held on by being screwed to the rims. Tires can only be filled with

air, no fluids or solids ( tires within a tire are considered reinforcements ) ( tires marked tubeless may have tubes inserted in them.) Remove all wheel

balance weights inside and out.

4. A MAXIMUM OF FIVE (5) GALLONS OF GASOLINE WILL BE ALLOWED. GAS TANKS must be moved to truck bed just aft of the rear window,

or in the case of a extended, four door cab it can be located in the back seat area if properly covered by a metal firewall. Trucks with tanks located

inside the frame mid vehicle can be left but should be covered with a skid plate to help protect being punctured from track side. Only unleaded

gasoline with a maximum octane level of 93 will be permitted. BOOSTED or RACING FUEL will not be allowed. If you have a truck equipped with a

fuel pump in the gas tank, you must install a emergency cut off switch upon the dash with a red circle painted around it. No external fuel pumps will be

allowed within the drivers compartment. If you run gas lines in the drivers compartment they must be double lined & double clamped. (a fuel line within

another line.)

5. ONLY ONE (1) STOCK BATTERY will be allowed. A maximum of 1200 cold cranking amps will be permitted. It must be incased in some way to

catch any leaking acid if it should become ruptured. It may be moved into the passenger floorboard area. Must be mounted & covered for participants

safety.

6. NO REINFORCEMENTS OF ANY KIND WILL BE ALLOWED. Only exceptions will be the driver side front door. Reinforcement bars or plates

added to the drivers side doors may not exceed eight inches (8") past the vertical seams of the door. You may also create roll over bars on the interior

or exterior cab(to prevent top of cab collapsing). Truck beds( See Number 7) . Trailer hitches or any type of stiffening device are considered

reinforcements. You may Weld rear ends or differentials to create a positive traction rear end. Rear ends cannot be chained. No interchangeable

rear ends. Only stock rear ends. No solid shocks or adding extra clamps or springs to suspension (suspension must work). Welding of bumper

shocks are considered reinforcements. Maximum bumper height is 22 inches from the ground to the center of the bumper. It is suggested that you

attach two vertical metal rods or chains approximately 12 inches from each end of the windshield opening to protect driver from hood coming off of

hinges and collapsing back in to the driver compartment.

7. STANDARD EXHAUST SYSTEM may be removed or cut off just aft of the front seats. Do not position exhaust to deflect the heat out to the side of

the vehicle. Additional headers, stacks, or custom manifolds cannot protrude past the level of the hood or through the body of the truck etc.

8. DO NOT WELD OR BOLT hoods down. Use wire. All doors must be chained shut or welded secure. If a driver's side door comes open, he or she

will be disqualified. If doors are welded, a maximum of 3- four inch welds in length on 2- vertical seams per door will be permitted. Truck tailgates must

be factory or none at all. Factory tailgate must be welded shut with a maximum of six 4 inch welds(welds maybe vertical or horizontal). Factory Pickup

Beds only. No wooden, steel flat beds, or dump beds allowed. You are permitted to fasten the truck bed down with six additional fasteners or four

inch welds. You may weld the steering sectors. Bumpers must be stock only. No Commercial bumpers, car bumpers, wooden bumpers, or

homemade fabricated bumpers. No tow hitches, brush guards, or running boards.

9. A 10 BY 12 INCH HOLE must be cut into the center of hood. To allow for early fire detection. ALL Metal Fan Blades must be removed. They may

be replaced with polycarbonate plastic blades. Only exception will be if your truck is equipped with a slip clutch fan blade and fan shroud or came stock

with an electric fan and shroud. You may create your own fan shroud out of some type of thin metal material & replace stiff original fans with slip

clutch fans. You may use electric fans ( only one) on trucks that did not come equipped with them from the factory.

10. PRIOR TO BRINGING TRUCK TO FAIRGROUND radiators must be drained and back flushed of all antifreeze coolants. They then can be refilled

with water or any of the new naturally biodegradable coolants. You must evacuate all air conditioning apparatus (lines & pumps) and gas refrigerant

coolants from your vehicles. Transmission coolers may be used but must stay within the engine compartment. (under the hood)

11. SAFETY BELTS, HELMETS (DOT approve), AND IMPACT RESISTANT EYE PROTECTORS are required. If truck was equipped with a shoulder

restraint system including lap belt, both must be used. Driver can be disqualified at any time if either belt or helmet is removed during a heat. Diver's

must wear long sleeve shirts & Pants. No electronic communications between driver and any other individuals permitted. NO TWO WAY RADIO'S. No

deliberate head-on collisions or deliberately ramming a driver's door. This can lead to disqualification. A TIME LIMIT will be set by the judges. IF A

DRIVER DOES NOT HIT A LIVE TRUCK WITHIN THE TIME LIMIT, this can lead to disqualification. No Possums!

12. ADDITIONAL SAFETY REGULATIONS MAY BE IMPOSED depending on the track. Rules are subject to change to fi t the event . If you have any

safety concerns. Call 1-888-361-5767 THE DECISION OF JUDGE IS FINAL. ANY DRIVER NOT OBEYING THE RULES WILL BE

DISQUALIFIED.

13. ALL TRUCKS MUST BE REMOVED FROM GROUNDS BY THE OWNER NO LATER THAN 7:00 A.M. THE NEXT DAY FOLLOWING THE

DERBY. THIS IS YOUR RESPONSIBILITY, so make arrangements before derby time.

Example of types of Compact Trucks that you may consider top use.

Datsun

Luv

Isuzu Rodeo

Mitsubishi Triton

Mitsubishi Mighty Max Nissan Frontier

(1998-2004)

Toyota

Courier

Chevy S 10

Hilux

Aro

Isuzu

Mitsubishi

Ford Ranger

Arrow Truck

UAZ

Forte

Mazda

Ram 50

Mazda B-Series

Isuzu P' up

Peugeot

SET# 5 STONEY ROBERTS DEMOLITION DERBY

Full Size Pick-up Trucks & Vans

DOMESTIC OR FOREIGN

1. ANY FOREIGN OR DOMESTIC FULL SIZE STOCK PICK-UP TRUCK or VAN up to 3/4 tons. Trucks may be two orfour door with extended cab.

Vans may be up to 15 passengers, and cargo vans. You may us four wheeled drive models: if four wheeled drive one of the drive trains must be

disconnected (Your Choice). No Jeep Wranglers, CJ 5, or CJ 7. No Super heavy Duty, Commercial, or Military duty Vehicles. No Soft tops or

Fiberglass tops.

2. ALL GLASS AND CHROME TRIM and anything that might become imbedded in the track, must be removed from the truck before bringing it to the

grounds. Also, Fire walls must remain in place. They cannot be sectioned or deleted. Do not leave broken glass in doors, clean them out.

WINDSHIELDS MUST BE REMOVED. All AIR BAG SAFETY SYSTEMS this includes activation charges must be removed. You must place some type

of screen in two door pick-ups back glass opening to prevent arms or head from extending from the opening. It is suggested to pad drivers side doors &

rig a headrest or padding behind all two door truck seats to protect the driver also. You may cut holes in upper sections of cargo vans that have solid

sides to aid in driver visual sight paths.

3. TIRES MUST BE STOCK SIZE, Truck tires can be up to 8 ply, no inner liner, no wire spoked rims, no split rims. Mud & Snow okay, no paddle

tires with tractor or ATV aggressive tread. No spoked rims, valve stem guards, or tires held on by being screwed to the rims. Tires can only be filled with

air, no fluids or solids ( tires within a tire are considered reinforcements ) ( tires marked tubeless may have tubes inserted in them.) Remove all wheel

balance weights inside and out.

4. A MAXIMUM OF FIVE (5) GALLONS OF GASOLINE WILL BE ALLOWED. GAS TANKS must be moved to truck bed just aft of the rear window,

or in the case of a extended, four door cab it can be located in the back seat area if properly covered by a metal firewall. Trucks with tanks located

inside the frame mid vehicle can be left but should be covered with a skid plate to help protect being punctured from track side. Only unleaded

gasoline with a maximum octane level of 93 will be permitted. BOOSTED or RACING FUEL will not be allowed. If you have a truck equipped with a

fuel pump in the gas tank, you must install a emergency cut off switch upon the dash with a red circle painted around it. No external fuel pumps will be

allowed within the drivers compartment. If you run gas lines in the drivers compartment they must be double lined & double clamped. (a fuel line within

another line.)

5. ONLY ONE (1) STOCK BATTERY will be allowed. A maximum of 1200 cold cranking amps will be permitted. It must be incased in some way to

catch any leaking acid if it should become ruptured. It may be moved into the passenger floorboard area. Must be mounted & covered for participants

safety.

6. NO REINFORCEMENTS OF ANY KIND WILL BE ALLOWED. Only exceptions will be the driver side front door. Reinforcement bars or plates

added to the drivers side doors may not exceed eight inches (8") past the vertical seams of the door. Truck beds( See Number 7) . Trailer hitches or

any type of stiffening device are considered reinforcements. You may Weld rear ends or differentials to create a positive traction rear end. Rear ends

cannot be chained. No interchangeable rear ends. Only stock rear ends. No solid shocks or adding extra clamps or springs to suspension

(suspension must work). Welding of bumper shocks are considered reinforcements. Maximum bumper height is 26 inches from the ground to the

center of the bumper. It is suggested that you attach two vertical metal rods or chains approximately 12 inches from each end of the windshield

opening to protect driver from hood coming off of hinges and collapsing back in to the driver compartment.

7. DO NOT WELD OR BOLT hoods down. All doors must be secured with Chain or welded shut If a driver's side door comes open, he or she will be

disqualified. If doors are welded, a maximum of 3- four inch welds in length on 2- vertical seams per door will be permitted. Truck tail gates must be

factory or none at all. Factory tailgate must be welded shut with a maximum of eight- 4 inch welds (welds may be on the vertical or horizontal seams).

Factory Pick-up Beds only. No wooden, steel flat beds, or dump beds allowed. You are permitted to fasten the truck bed down with eight additional

fasteners or four inch welds. You may weld the steering sectors. You must cover the back cab window with some type of screen and place at least two

vertical hood bars within the windshield opening. ( To prevent hood from coming in on driver.) You should place a vertical bar/post running from the

floor board to the top of the cab bolted from inside out near the center of the back window. The post should be strong enough to act as a brace if you

should go inverted on your top. Bumpers must be stock only. No Commercial bumpers, car bumpers, wooden bumpers, or home made fabricated

bumpers. No tow hitches, brush guards, or running boards.

8. STANDARD EXHAUST SYSTEM may be removed or cut off just aft of the front seats. Do not position exhaust to deflect the heat out to the side of

the vehicle. Additional headers, stacks, or custom manifolds cannot protrude past the level of the hood or through the body of the truck etc.

9. A 10 BY 12 INCH HOLE must be cut into the center of hood. To allow for early fire detection. ALL Metal Fan Blades must be removed. They may

be replaced with polycarbonate plastic blades. Only exception will be if your truck is equipped with a slip clutch fan blade and fan shroud or came stock

with an electric fan and shroud. You may create your own fan shroud out of some type of thin metal material & replace stiff original fans with slip

clutch fans. You may use electric fans ( only one) on trucks that did not come equipped with them from the factory.

10. PRIOR TO BRINGING TRUCK TO FAIRGROUND radiators must be drained and back flushed of all antifreeze coolants. They then can be refilled

with water or any of the new naturally biodegradable coolants. You must evacuate all air conditioning apparatus (lines & pumps) and gas refrigerant

coolants from your vehicles. Transmission coolers may be used but must stay within the engine compartment. (under the hood)

11. SAFETY BELTS, HELMETS (DOT approve), AND IMPACT RESISTANT EYE PROTECTORS are required. If truck was equipped with a shoulder

restraint system including lap belt, both must be used. Driver can be disqualified at any time if either belt or helmet is removed during a heat. Diver's

must wear long sleeve shirts & Pants. No electronic communications between driver and any other individuals permitted. NO TWO WAY RADIO'S. No

deliberate head-on collisions or deliberately ramming a driver's door. This can lead to disqualification. A TIME LIMIT will be set by the judges. IF A

DRIVER DOES NOT HIT A LIVE TRUCK WITHIN THE TIME LIMIT, this can lead to disqualification. No Possums!

12. ADDITIONAL SAFETY REGULATIONS MAY BE IMPOSED depending on the track. Rules are subject to change to fi t the event . If you have any

safety concerns. Call 1-888-361-5767 THE DECISION OF JUDGE IS FINAL. ANY DRIVER NOT OBEYING THE RULES WILL BE

DISQUALIFIED.

13. ALL TRUCKS MUST BE REMOVED FROM GROUNDS BY THE OWNER NO LATER THAN 7:00 A.M. THE NEXT DAY FOLLOWING THE

DERBY. THIS IS YOUR RESPONSIBILITY, so make arrangements before derby time.